The 4-band code is used for marking low precision resistors with 5%, 10% and 20% tolerances. Identifying the value will become easy with a little practice, as there are only a few simple rules to remember:
The standard resistor color code table:
Color | 1st digit | 2nd digit | 3rd digit* | Multiplier | Tolerance | Temp. Coef. | Fail Rate |
---|---|---|---|---|---|---|---|
Black | 0 | 0 | 0 | x10^{0} | |||
Brown | 1 | 1 | 1 | x10^{1} | ±1% (F) | 100 ppm/K | 1% |
Red | 2 | 2 | 2 | x10^{2} | ±2% (G) | 50 ppm/K | 0.1% |
Orange | 3 | 3 | 3 | x10^{3} | 15 ppm/K | 0.01% | |
Yellow | 4 | 4 | 4 | x10^{4} | 25 ppm/K | 0.001% | |
Green | 5 | 5 | 5 | x10^{5} | ±0.5% (D) | ||
Blue | 6 | 6 | 6 | x10^{6} | ±0.25%(C) | ||
Violet | 7 | 7 | 7 | x10^{7} | ±0.1% (B) | ||
Gray | 8 | 8 | 8 | x10^{8} | ±0.05%(A) | ||
White | 9 | 9 | 9 | x10^{9} | |||
Gold | x0.1 | ±5% (J) | |||||
Silver | x0.01 | ±10% (K) | |||||
None | ±20% (M) |
* 3rd digit - only for 5-band resistors
So, for a 560 ohm, 5% resistor the color stripes will be green, blue, brown and gold. Green and blue are the first significant digits (56); brown is the multiplier (10^{1} = 10) and gold is the tolerance (5%). 56 x 10 = 560Ω.
If the 3rd band would be red instead of brown, the multiplier would be (10^{2} = 100) instead of 10 and the resistor value would be 56 x 100 = 5600 ohms = 5.6 k ohms.
云南快乐十分遗漏前三 if the multiplier band is gold or silver, then the decimal point is moved to the left one or two places (divided by 10 or 100). for example, a resistor with green, blue, silver and gold rings has a value of 56 x 0.01 = 0.56Ω.
The 5 band code is used for marking high quality, precision resistors with 2%, 1% or lower tolerances. The rules are similar to the previous system; the only difference is the number of digit bands. The first 3 bands will represent the value, the 4th band will be the multiplier and the 5th stripe will give us the tolerance.
A few resistors have an additional band - often giving beginners a bit of trouble - indicating either the reliability or the temperature coefficient.
The reliability band specifies the failure rate per 1000 hours (assuming that a full wattage being applied to the resistor). This stripe is found primarily on 4-band resistors made for military applications and seldom used in commercial electronics.
The temperature coefficient is more commonly marked, especially on quality 5-band resistors, as it starts to become an important factor for precision components. For a resistor with temperature coefficient of 200 ppm, for example, a change in temperature of 50°C causes a value change of 1%. The most common values for this band are presented in the color chart above.
Four band code:
Green, blue, red, with silver tolerance band: 56 x 100 = 5.6 kohms, with a tolerance of 10%
Brown, black, orange, gold tolerance band: 10 x 1000 = 10000 ohms (or 10K ohms), with a tolerance of 5%
Red, red, brown, silver tolerance band: 22 x 10 = 220 ohms (220 ohms), with a tolerance of 10%
More 4 band resistor color code examples: E12 and E24 series.
Five band code:
Blue, brown, white, brown, red tolerance band: 619 x 10 = 6190 ohms (6.19K ohms), with a tolerance of 2%
Red, red, brown, black, with a brown tolerance band: 221 x 1 = 221 ohms, with a tolerance of 1%
云南快乐十分遗漏前三 Brown, black, black, red, with a brown tolerance band: 100 x 100 = 10000 ohms (10.0K), with a tolerance of 1%
Resistors are available in standard values such as 1K, 2.2K, 4.7K, and so on. The two most common standards are the E12 and E24云南快乐十分遗漏前三. You will notice that in the E12 series each succeeding value falls within +/- 10% of the previous value. The E24 range includes all of the E12 values, plus a further 12 to enable the selection of more precise resistances.
the e6 (20%) range is a subset of the e12 (10%) range and the e12 range is a subset of the e24 (5%) range. similarly, the e48 (2%) range is a subset of the e96 (1%) range and the e96 range is a subset of the e192 (0.5% or less) range. note, that the e24 range is technically also a subset of the e48 range, however, because of the different number of digits used for representation and rounding errors, the corresponding values in the two series do not match.
E6 series: (20% tolerance)
10, 15, 22, 33, 47, 68
E12 series: (10% tolerance) - examples...
10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82
E24 series: (5% tolerance) - examples...
10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91
E48 series: (2% tolerance) - examples...
100, 105, 110, 115, 121, 127, 133, 140, 147, 154, 162, 169, 178, 187, 196, 205, 215, 226, 237, 249, 261, 274, 287, 301, 316, 332, 348, 365, 383, 402, 422, 442, 464, 487, 511, 536, 562, 590, 619, 649, 681, 715, 750, 787, 825, 866, 909, 953
E96 series: (1% tolerance)
100, 102, 105, 107, 110, 113, 115, 118, 121, 124, 127, 130, 133, 137, 140, 143, 147, 150, 154, 158, 162, 165, 169, 174, 178, 182, 187, 191, 196, 200, 205, 210, 215, 221, 226, 232, 237, 243, 249, 255, 261, 267, 274, 280, 287, 294, 301, 309, 316, 324, 332, 340, 348, 357, 365, 374, 383, 392, 402, 412, 422, 432, 442, 453, 464, 475, 487, 491, 511, 523, 536, 549, 562, 576, 590, 604, 619, 634, 649, 665, 681, 698, 715, 732, 750, 768, 787, 806, 825, 845, 866, 887, 909, 931, 959, 976
so, why all this trouble with color coding? the resistance value could be stamped or painted on the body of the through-hole resistor, no?
yes, but the numbers would be quite small and difficult to read. if such a resistor is mounted with the marked side down, you cannot read its value unless you take it out of the circuit. also, the markings would easily rub off or become smeared with time.
The resistor color code云南快乐十分遗漏前三 might seem a bit confusing and rather inconvenient at first, but most electronics hobbyists and technicians are surprised when they realize how quickly they've memorized the color chart without the use of mnemonics or other silly shortcuts.
云南快乐十分遗漏前三 the color code is quite intuitive, and after a brief familiarization period, instantly recognizing resistor values will come as second nature.